<\/p>\n
JY1SAT CubeSat<\/p>\n<\/div>\n
JY1Sat is an enhanced 1U FUNcube. It has been developed for the Crown Prince Foundation in Jordan. The spacecraft has been named in honour of the Crown Prince\u2019s grandfather, King Hussein, who operated using his personal amateur radio callsign which was simply JY1.<\/p>\n
In addition to the usual suite of FUNcube capabilities it will also be capable of downlinking images in SSDV\u00a0format<\/a>.\u00a0 This image format, developed by Phil Heron, MI0VIM<\/strong><\/a>, for use in High Altitude Balloons<\/a>, is now also being used from lunar orbit by AO-94<\/a>.<\/p>\n The telemetry downlink frequency is 145.840 MHz, this will use the usual FUNcube standard 1k2 BPSK format. The linear transponder, for Single Sideband (SSB) and CW modes, will downlink on 145.855-145.875 MHz and uplink on 435.100-435.120 MHz. The transponder is inverting so Lower Sideband (LSB) should be used on the uplink and Uppersideband (USB) on the downlink.<\/p>\n A new Dashboard has been developed for this mission and is available for download here<\/a>:<\/p>\n This will operate in exactly the same manner as those developed for previous missions and general set-up information can be downloaded here:\u00a0Dashboard Guidance<\/a><\/p>\n A brand new Data Warehouse has also been created. This can be used to view the telemetry from ALL of the FUNcube missions. This can his can viewed here http:\/\/data2.amsat-uk.org\/<\/a><\/p>\n SSO-A Mission Patch<\/p>\n<\/div>\n This mission will be one of the payloads on the Spaceflight SSO-A mission. This is currently scheduled to lift-off on Monday, November 19, 2018 at 18:32 GMT from the Vandenberg Air Force base in California. This launch is expected to have more than sixty other payloads.<\/p>\n The deployment time for JY1SAT has been advised as 4 hours 31 minutes and 54.5 seconds after launch. This means that, allowing for the pre-programmed delay of 30 minutes between deployment from the POD and the release of the antennas, the first downlink signals cannot be expected until approximately 23:34 GMT on November 19.<\/p>\n Watch the launch at https:\/\/www.youtube.com\/watch?v=PJkRM5QQDAA<\/a><\/p>\n Here are some initial pre-launch TLEs which we believe will be accurate for at least the first few orbits.<\/p>\n JY1-Sat Provisional SatPC32<\/a> Doppler.sqf data for tracking JY1SAT and other Amateur Radio satellites on SSO-A at https:\/\/gist.github.com\/magicbug\/cf23cfca3a6ec9902d8dd9326a9249ea<\/a><\/p>\n Initial indications are that the spacecraft will be over NE Australia at power-up.<\/p>\n The start-up mode, as usual, is low power telemetry only and we will be really looking forward to receiving reports\u00a0 and telemetry. So please, either upload the data from the Dashboard to the Warehouse in the usual way, or send a quick email to operations@funcube.org.uk<\/a><\/p>\n<\/div>\n Get The Details…<\/a><\/p>\n m5aka<\/p>\n AMSAT-UK<\/p>\n Powered by WPeMatico<\/a><\/small><\/p>\n","protected":false},"excerpt":{"rendered":" <\/p>\n JY1SAT CubeSat<\/p>\n JY1Sat is an enhanced 1U FUNcube. It has been developed for the Crown Prince Foundation in Jordan. The spacecraft has been named in honour of the Crown Prince\u2019s grandfather, King Hussein, who operated using his personal amateur radio callsign which was simply JY1.<\/p>\n In addition to the usual suite of FUNcube capabilities it will also be capable of downlinking images in SSDV\u00a0format<\/a>.\u00a0 This image format, developed by Phil Heron, MI0VIM<\/strong><\/a>, for use in High Altitude Balloons<\/a>, is now also being used from lunar orbit by AO-94<\/a>.<\/p>\n The telemetry downlink frequency is 145.840 MHz, this will use the usual FUNcube standard 1k2 BPSK format. The linear transponder, for Single Sideband (SSB) and CW modes, will downlink on 145.855-145.875 MHz and uplink on 435.100-435.120 MHz. The transponder is inverting so Lower Sideband (LSB) should be used on the uplink and Uppersideband (USB) on the downlink.<\/p>\n A new Dashboard has been developed for this mission and is available for download here<\/a>:<\/p>\n This will operate in exactly the same manner as those \u2026 Continue reading ![\"SSO-A](\"https:\/\/ukamsat.files.wordpress.com\/2018\/11\/sso-a-mission-patch.jpg?w=300&h=300\")
<\/a><\/p>\n
\n1 50001U 18001A 18323.01450000 .00000000 00000-0 30100-5 0 9992
\n2 50001 97.7750 30.5000 0012840 225.0000 124.7930 15.00300000 11<\/p>\nJY1SAT Launch Information and Dashboard<\/h2>\n<\/p>\n